Square corner faceplates give your door a clean refined look. In this post, we’ll discuss the s tandard door lock hole size and its various applications. As there are many locksmith tricks to try, it’s advisable to use a latch with an attached faceplate for exterior doors as they seem to be well suited for the exterior. Need Help? If your doors are not prepped this way, but you want a faceplate, we recommend purchasing locks with square corner faceplates below as it is much easier to chisel out square corners than rounded. In addition to the two cross bores, a door can be prepped for one of 3 different types of latches. Size/Measurement. For other door thicknesses, specify size . We're Here Mon-Fri 9-5 Mtn Time: Most interior doors are prepped with a single boor hole. Trace the bolt plate's outline … If your doors are not well-prepared, but you want to install a faceplate, consider purchasing locks with square cornered faceplates because they’re much easier to chisel out than round ones. If you’re keen on getting faceplates, but your door isn’t properly prepped, you can easily prep it for square corner faceplate latches using a 1” chisel. Bore a 1-inch hole in the edge of the door located on the centerline of the 2-1/8-inch … Just going to install a schlage connect into a door without an existing deadbolt. Most door hardware will fit the following door preparation. Standard cross bores measure about 1 inch in diameter. Do install the latch, all you have to do is slide it into the cross bore and tap it into place gently with a mallet or hammer. Position the … The standard preparation for a door with both a deadbolt and doorknob has two sets of cross bore and dead bore holes stacked on top of each other at 5 1/2 inches from one center to another. Be sure to buy a lockset that will fit your door’s thickness. This is the metric equivalent to 2.5" and 3" lock cases from back in the imperial days. While this works and is easier to install, it just looks nicer if you prep the door for matching latches. 2 Screw hole-boring template to door for drilling out the lockset holes. A non-tested night latch can be used for access but it must be supported with a tested lock so you would have two locks on the door. If your doors are prepared for radius corner faceplates but you’re more interested in square ones — chiseling out the very corner is a no-brainer. (This is the backset dimension.) hole saw (this is the standard size for most locksets; check your lockset’s instructions to verify this dimension), … Installation at 40 inches is common on affordable … The backset is the distance from the edge of the door to the center line of the prepared cross bore hole drilled to install most locks. If you're installing several doors, it's acceptable to drill the doorknob hole at 40 inches, or centered vertically. Drill holes 1/2 way through door then complete from other side to prevent splitting. In this post, we’ll discuss the standard door lock hole size and its various applications. If you want faceplates, but your door is prepped for drive in latches you can easily prep your door for these using a 1" chisel. Round,Off White Pack of 10 4.4 out of 5 stars 58 $6.99 $ 6 . 6 Set latch into hole, and mark its outline on door … It’s important, however, to know whether your door is prepared for door hardware that fits the standard door lock hole size. When replacing an existing door with a pre-hung door, select a door that has the same dimensions as the existing one. Pocket Door Lock Drilling Instructions Single-Sided Deadbolt Drilling Instructions Drilling Template for Knobs, Levers, Deadbolts *Drilling template must be printed at 100% exact size Connect with us. Now that you know the standard door lock size, you can determine the most appropriate preparation of the three possible types of latches you may be interested in installing. For most interior doors, all you need is a single bore hole. Schlage aged bronze one sided deadbolt the best door lock reviews by wirecutter schlage encode smart wifi deadbolt best smart locks 2020 reviews by Need help finding the right Door Hardware for your application? Usually, … Backset: The distance between the edge of the door and the center of the lock hole. Drill out the holes with the correct size hole saw, then insert the lock … 2-1/8" (54mm) Dia. Want to be a futurist? Doors are typically either 1 3/8 inches or 1 3/4 inches thick. Is your door prepped for door hardware that won't fit the standard door preparation as we have described here? These square corner faceplates give your door a refined clean look. 5 Unscrew template from door. Installing the latch simply involves sliding it into the cross bore and using a hammer or mallet to gently tap it into position. Door openings and dimensions are especially important when installing or replacing an interior door. Perfect for a new storm door installation as well as a replacement handle set on your existing Andersen storm door … Drive-in latches are the easiest to install. - Your door must have a minimum of 5 1/2" between the center of the deadbolt crossbore hole and the center of any other door latch below the deadbolt. If you have something different, please contact us so we can help you find exactly what you need. The standard sizes bore hole is 2 1/8” in diameter while the cross bore is usually about 1” in diameter. The standard sized bore hole is 2 1/8" in diameter. The hole diameters are 2 and 1/8-inch and 1-inch respectively. Start by cultivating these four habits, 5 Unexpected Sources For UX Design Inspiration, The 4 biggest challenges to starting a career in UX. There is also a cross bore where the latch is installed, that usually extends from the edge of the door through the bore hole.